Varmint Rifle Monopod

Attention Varmint Shooters!

Be sure to to read the On Target Magazine article where they discuss using the P3 Ultimate Rifle Monopod on varmint rifles.

Read the entire On Target Varmint Rifle Monopod article.

- Curt

Smith and Wesson M&P15VTAC

Our P3 Mono Grip is once again used during an On Target AR review. This time our forward grip is mounted on the Smith & Wesson M&P15VTAC.

Read the entire Smith & Wesson M&P15VTAC Review.

- Curt

Stag Arms Model 2T

On Target Magazine tests the Stag Arms Model 2T. During testing, the 2T was equipped with our P3 Mono Grip.

Read the entire Stag Arms Model 2T Review.

- Curt

ArmaLite AR-50 Carrying Handle

Be sure to check out the Small Arms Review article written about our AR-50 Carrying Handle.

- Curt

On Target Magazine Jun07

On Target Magazine Jun07
by Ben Battles

PROJECT GUN
Williams Gun Sight Co.
Project 700

Photo caption (far upper/right photo):
Our 700's red base coat shows through in the form on an On Target logo and light hues throughout. The CTK Precision (ctkprecision.com) P3 Monopod is extremely well made and a handy tool for supporting the rear of a heavy precision rifle.

Click here to read the entire article.

Gun Digest Jun07

Gun Digest Jun07

P3 Mono-Grip from CTK Precision Is Foregrip and Monopod In One

The P3 Mono-Grip turns a vertical foregrip into a shooting rest with a twist of the wrist. The P-3 provides a rock-solid support but still provides flexibility and versatility when you need it most. The design lets you immediately pivot your firearm from left to right to get on target quickly.

CNC machined from billet aluminum for high strength and light weight (6.4 ounces), it comes with a durable mil-spec hard-coat anodized finish and flat sides for pressure switches. A collapsed height of 4.75 inches and an extended height of 8 inches allows the use of a 30-round magazine. The spring-loaded pop-out design adjusts from a grip to a monopod in seconds. The durable rubber foot resists movement and will not harm surfaces. The P-3 fits all picatinny 1913 rails.

Contact CTK PRECISION at (715) 754-2891 or www.ctkprecision.com.

Gun and Weapons for Law Enforcement Feb07

Guns and Weapons for Law Enforcement Feb07

ULTIMATE MONO-POD

Just released by CTK Precision is the P3 Ultimate Mono-Pod. Using a quick-change system, the P3 attaches to the rear sling swivel stud in seconds without tools and won't scratch the stock. Made of CNC machined aluminum, the P3 has a matte black hard coat anodized finish. The 2-stage telescoping leg provides 360 inches of elevation at 100 yards. The cam-locking 1st stage gets you on target fast, while the 2nd stage lets you fine-tune. The P3 is only 2.7 inches in the collapsed position and weighs just 5.4 ounces. An additional QD sling mount (furnished) allows the sling to be mounted on either side of the P3. An adaptor for AR-15 stocks is also available. For information, contact CTK Precision, E5861 Herzberg Rd, Dept GW/LE, Marion, WI 54950; 715-754-2891; www.ctkprecision.com

Click here to read the entire article.

Special Weapons Jan07

Special Weapons Jan07
by Charlie Cutshaw


Tactical Rifles M40A3

Click here to read the entire article.

Just prior to testing, we were sent a new and innovative product for CTK Precision. This patent pending device, called the P3 Ultimate Monopod, is a quick detach monopod that fits any rifle by attaching to the rear swivel stud. An adapter for AR-type precision rifles is also available. Some rifles come equipped with monopods, as they add stability in some scenarios, but most do not and for those shooters who want a monopod, the P3 is just the ticket. The P3 Ultimate Monopod is CDC machined from billet aluminum and hard coat anodized. When the P3 is attached to the rifle, the bottom of the mounting screw takes the place of the sling swivel adapter. There are threaded side mounts and studs for those who might wish to use a side-mounted sling. The P3 Monopod has both gross and fine adjustments. Gross adjustment is attained by rotating a locking nut so the spring-loaded leg can be lowered. Once the gross adjustment is achieved, turning the monopod a quarter turn counterclockwise locks it in place. The monopod is fine tuned using a threaded segment with a rotating Delrin foot. When collapsed, the P3 Ultimate Monopod extends only a little over 2 inches below the stock. The monopod has rubber pads to protect the rifle stock. When not in use as a monopod, the devise serves as a handy grip to pull the rifle back into the shooter's shoulder.

Click here to read the entire article.

S.W.A.T. Magazine Aug06

S.W.A.T. Magazine Aug06
by Leroy Thompson

P3 Shooting Rest and Gun Vise

Since I live in a condo these days I have to limit the amount of space I can devote to all of those accessories which make working on firearms or shooting easier. As a result, I am always on the lookout for devices which are simple, compact and multifunctional. That's why I like the P3 Ultimate Shooting Rest and P3 Ultimate Gun Vise Attachment.

The Ultimate Gun Rest may be used for sighting, testing groups or chronographing either pistols or rifles. By carrying out a quick conversion, the P3 Shooting Rest becomes the P3 Gun Vise which allows easy cleaning, repair, bore sighting or other tasks on the rifle, shotgun, submachine gun or the major subgroups such as the barreled action or stock.

The Ultimate Shooting Rest allows easy adjustments to properly position nearly any firearms for shooting. The shooting rest is of heavy duty steel construction with a wide front V rest that first all firearms. The rear shooting pad and the V rest are padded to protect the weapon from scratching. Note, too, that the padding is solvent safe to allow no-worry cleaning. The feature that makes the P3 Shooting Rest so useful for sighting in scopes or adjusting sights is the ease of adjustment. The base has a three point leveling system with thumb locks that allow it to remain very solid on a shooting bench. The rear shooting pad telescopes so it may be adjusted for height and angle to fit the weapon being shot. The front V rest also telescopes. A useful feature of the rear rest is that the carpet which covers it has a center groove which helps create a tight fit and also allows a rifle to be sighted without removing swivel studs. If one plans to sight both rifles and pistols, the changeover is as simple as sliding the rear shooting pad forward for pistols or to the rear for long guns.

Click here to read the entire article.